Materials we manufacture / PA
PA6-CF30 HS
Filament guide.
WJ PA6-CF30 HS is a carbon-fibre reinforced PA6 filament. Review its grade-specific reference properties, printing parameters and handling guidance.
WJ-TDS-PA6-CF30-HS-001 · Rev V1.0 · Issued 2026-10-20
- Nozzle temperature
- 275 °C
- Bed temperature
- 100 °C
- Printing speed
- 120-150 mm/s
Technical data sheet
Overview & applications.
WJ PA6-CF30 HS is a carbon-fibre reinforced PA6 filament. Review its grade-specific reference properties, printing parameters and handling guidance.
Typical applications
Application suitability must be verified for the intended part design, loading and environment. The supplied reference sheet does not specify application categories.
Technical data sheet
Recommended printing parameters.
Use the grade-specific ranges as a starting point and tune settings for your printer and part geometry.
| Parameter | Unit | Value |
|---|---|---|
| Nozzle temperature | °C | 275 |
| Bed temperature | °C | 100 |
| Build surface material | - | PEI film, PI film |
| Cooling fan | - | OFF |
| Printing speed | mm/s | 120-150 |
| Environmental temperature | °C | 40-60 |
| Annealing (after printing) | °C | 100-120 |
| Annealing time | - | Not specified in the supplied reference sheet. |
This technical data sheet provides typical reference values for material comparison and selection only. It is not an independent third-party test report and does not constitute a product specification, warranty or guarantee of performance. Test methods and specimen conditions are stated in the corresponding sections. The user must verify suitability for the intended application.
These values have not been independently re-tested by WJ on this batch.
Technical data sheet
Material properties.
Typical values from the original TDS. Preserve the test method and specimen orientation when comparing materials.
Physical & thermal properties
| Property | Test method | Unit | Typical value |
|---|---|---|---|
| Density | ISO 1183 | g/cm³ | 1.26 |
| Light transmission | N/A | - | N/A |
| Flame retardancy | N/A | - | N/A |
| Melting temperature | ISO 11357 | °C | 260 |
| Heat deflection temperature (0.45 MPa) | ISO 75-2 | °C | 178 |
| Vicat softening temperature (A50) | ISO 75-2 | °C | N/A |
Mechanical properties
| Property | Test method | Unit | Typical value |
|---|---|---|---|
| Tensile strength (X-Y) | ISO 527 | MPa | 85 |
| Tensile strength (Z) | ISO 527 | MPa | 46 |
| Elongation at break (X-Y) | ISO 527 | % | 3.9 |
| Elongation at break (Z) | ISO 527 | % | 2 |
| Bending strength (X-Y) | ISO 178 | MPa | 159 |
| Bending strength (Z) | ISO 178 | MPa | 76 |
| Bending modulus (X-Y) | ISO 178 | MPa | 8028 |
| Bending modulus (Z) | ISO 178 | MPa | 1577 |
| Charpy impact strength (X-Y) | ISO 179 | KJ/m² | 33 |
| Charpy impact strength (Z) | ISO 179 | KJ/m² | 11 |
Chemical & physical characteristics
| Parameter | Value |
|---|---|
| Composition | Carbon-fibre reinforced PA6. Fibre content is not specified in the supplied reference sheet. |
| Moisture sensitivity | Moisture-sensitive; keep below 20% relative humidity during storage and printing. |
N/A values remain as reported. Material-family compatibility statements require application-specific validation.
Technical data sheet
Data source & test conditions.
| Topic | Data source & test conditions |
|---|---|
| Data status | Typical reference values; not independently re-tested by WJ on this batch. |
| Reference revision | LW-TDS-A01; WJ edition V1.0. |
| Printing conditions | Recommended parameters are based on Bambu Studio with a 0.4 mm nozzle. Printing conditions may differ with other nozzle diameters. |
| Unspecified conditions | Specimen conditioning, infill, perimeter count, drying schedule and annealing duration are not specified in the supplied reference sheet. |
| Orientation labels | X-Y and Z labels are retained from the supplied reference sheet. Detailed specimen preparation is not specified. |
| Topic | Guidance |
|---|---|
| Typical, not minimum | Typical reference values for comparison only; not guaranteed finished-part performance. |
| N/A | N/A is retained as reported. It does not establish certification or compliance. |
| Grade identification | PA6-CF30 HS: use only the matching grade data sheet. Do not substitute another PA or PPA grade. |
Technical data sheet
Storage, handling & safety.
| Topic | Guidance |
|---|---|
| Nozzle wear | Use a wear-resistant nozzle, such as hardened steel or ruby. Brass nozzles are susceptible to wear. |
| Drying and moisture | Dry before printing. Store and print in dry conditions below 20% relative humidity. Drying temperature and duration are not specified in the supplied reference sheet. |
| Self-support removal | When using this filament as its own support material, remove supports before excessive moisture uptake; otherwise supports may bond permanently to the model. |
| Annealing | After printing, anneal the part at 100-120 °C to improve overall strength. Annealing duration is not specified in the supplied reference sheet. |
Technical data sheet
OEM & ordering.
| Topic | Ordering information |
|---|---|
| OEM & ordering | Confirm diameter, spool weight, colour, packaging, quantity and commercial terms with WJ. These are not specified in the supplied reference sheet. |
Confirm current commercial terms with WJ for your project.
Data disclosure
Disclaimer & data status.
Typical values are for reference and comparison only, not for design specifications or quality control. Actual properties depend on part design, environment, printing conditions and post-processing. Specifications may change without notice. The user must assess safety, compliance, technical suitability and end-of-life disposal or recycling for the intended application. WJ makes no warranty of suitability and accepts no liability for damage, injury or loss arising from use.
Typical reference values / no third-party report
This technical data sheet provides typical reference values for material comparison and selection only. It is not an independent third-party test report and does not constitute a product specification, warranty or guarantee of performance. Test methods and specimen conditions are stated in the corresponding sections. The user must verify suitability for the intended application.
These values have not been independently re-tested by WJ on this batch. They must not be interpreted as results of WJ internal testing.
PDF disclosure addendum A1 · 2026-10-20. Numerical properties and processing ranges are unchanged.
Technical data sheet
Original TDS & revision.
| Rev | Date | Description | Approved |
|---|---|---|---|
| V1.0 | 2026-10-20 | First WJ edition. Numerical values and test methods retained from the supplied reference sheet. | WJ |
Document WJ-TDS-PA6-CF30-HS-001. This TDS is not a batch certificate of analysis or conformity.
Continue exploring
More in the PA range.
Questions before you order
Answers from this grade’s published technical data and WJ’s public OEM information.
What nozzle and bed temperatures should I start with?
Nozzle temperature: 275 °C; Bed temperature: 100 °C. These are grade-specific TDS starting points. Tune settings for your printer, colour and part geometry.
How should I dry and store this filament?
Drying before printing: Not specified in this printing table. Confirm the exact requirement with WJ before use. Read the grade-specific guide and download the TDS. Printing and storage humidity: Not specified in this printing table. Confirm the exact requirement with WJ before use. Read the grade-specific guide and download the TDS.
Does this grade require an enclosure or a specific nozzle?
Enclosed chamber: Not specified in this printing table. Confirm the exact requirement with WJ before use. Read the grade-specific guide and download the TDS. Nozzle type: Not specified in this printing table. Confirm the exact requirement with WJ before use. Read the grade-specific guide and download the TDS. These are grade-specific TDS starting points. Tune settings for your printer, colour and part geometry.
Are the TDS values guaranteed properties of my printed part?
No. These are typical reference values under the stated test methods and specimen conditions. They are not an independent third-party test report or a guarantee of printed-part performance. Check the data-source disclosure and validate your application.
Which technical document belongs to this grade?
Use the matching document: WJ-TDS-PA6-CF30-HS-001; Revision V1.0; 2026-10-20. Read the grade-specific guide and download the TDS.
Can I order custom colours or private label packaging?
WJ publishes a custom-colour MOQ of 100 kg per colour on its homepage. Confirm this grade’s colour availability, samples, batch quantity, spool, labels, packaging and lead time with the team; this is not a universal MOQ for every order. Discuss your OEM project.
Manufactured for your brand
Build your PA6-CF30 HS filament range.
Discuss colours, spool options, labels and packaging with our team. Share your material, quantity and destination for an OEM quote.